The MB CRDL Cradling Broom is designed for efficient snow removal on airports, with an in-line stowing and cradling design for transport and storage. When cradled, the casters lift off the ground to eliminate damage during transport and extend caster life. The 46-inch-diameter broom is available in lengths of 18, 20, and 22 feet, providing swept paths up to 18 feet wide.

The content is machine translated.

MB |Jet sweeper|CRDL

Share by email

Cradling System

The CRDL features an in-line stowing and cradling design for transport and storage. When the broom is cradled, the casters lift off the ground to eliminate damage during transport and extend caster life.

Sweeping Unit

The CRDL features a 46-inch-diameter broom available in lengths of 18, 20, and 22 feet, providing swept paths up to 18 feet wide. The broom operates at 600 rpm with 4,024 foot-pounds of available torque at the broom shaft at 5,075 psi maximum working pressure. Brush material options include wire, poly, or alternating. The broom head also features amber and red marker lights.

Working Speed: The listed “working speed up to” indicates the estimated maximum technical speed the equipment can achieve. It does not represent the recommended operating speed. Actual operating speeds must always be adjusted to the prevailing weather and environmental conditions.

Broom Unit

Broom Head Configuration Options

The broom frame is 102 inches wide, while the broom head configuration options include:

  • 20-foot broom length
  • 22-foot broom length
  • Broom Power Package Options
     

The optional Broom Power Package includes a Caterpillar C13B 496 HP electronic turbocharged diesel engine that is T4F EPA/Stage 5 emission certified. It is available with a 500 rpm broom providing 4,828 foot-pounds of available torque at the broom shaft at 5,075 psi maximum working pressure.

 

Broom General Options

  • Automatic brush pattern adjustment
  • Broom head vibrator
  • Ground speed control, requiring automatic brush pattern adjustment and broom speed tachometer
  • Broom hydrostatic pressure gauge
  • Auto stripper bar adjustment system, requiring automatic brush pattern adjustment
  • Snow shed hood
  • Rear-view color camera system
  • 13 pounds of poly/wire alternating wafers in place of all poly wafers
  • Cassette brushes for faster replacement, available as single or dual core in poly, poly/wire, and all-wire bristles
  • Broom Spare Parts Options
     

Broom Spare Parts Options

  • Broom chassis axle, tire and wheel
  • Set of broom cores
  • Set of four non-adjustable broom carts
  • Set of two end plate jacks for core change
  • Caster tire and wheel, nitrogen filled
  • Caster tire, wheel, hub, bearings, axle, and nuts, nitrogen filled
  • Caster tire and wheel, foam filled
  • Caster tire, wheel, hub, bearings, axle, and nuts, foam filled
  • All-poly, all-wire, or poly/wire alternating wafer kits

Blower Unit

The CRDL is equipped with a dual-impeller, forced-air blower producing 23,000 cfm at 410 mph total.

Drive

The standard broom power package features a 375 HP electronic turbocharged diesel engine that is a Caterpillar C9.3B T4F EPA/Stage 5 emission certified. The engine includes ether start and a heated fuel water separator. A 150-gallon fuel tank provides approximately 12 hours of operation. The engine is housed in a butterfly fiberglass enclosure with hand power assist.

Motion Control

The CRDL features a 25,000-pound electronically controlled steering axle with ABS brakes and automatic drift control. The steering system includes provisions for centering and disengaging the axle steering system. The towing chassis determines the turning radius to ensure the broom consistently follows the chassis.

A center rotating bearing ensures the weight and location of the broom head remain on the carrier center line regardless of the position of the broom head. Independent broom head tilt compensates for surface variations and minimizes brush pattern deviation during operation. Broom oscillation is 8 degrees (+/-4°).

Operator Controls

Operator controls in the cab and engine enclosure promote operator safety and operations.

Power Transmission

Gearboxes with keyed tapered hubs prevent loose connections. Hardened steel pilot plates and core sprockets accommodate radial loads, while molded urethane drive cogs provide torque transmission.

Hydraulic and Electrical System

An independent auxiliary electric motor with hydraulic pump supports the hydraulics and jack stand. A battery disconnect switch removes power to the unit, and a broom speed tachometer is provided.

Engine Options

  • Broom engine oil pan heater, pad type
  • Broom engine block heater, immersion type
  • Battery trickle charger, 1.5 amp
  • Battery charger, 20 amp
  • Battery heater, pad type
  • Remote jump start battery lugs
  • Hydraulic oil tank heater, pad type
  • Fuel heater, pad tank type
  • Coolant filter

CRDL Chassis Integration of Towing Chassis

The CRDL Chassis Integration of Towing Chassis option includes:

  • Stationary fifth wheel and mounting
  • 9,000-lb ballast
  • Plow controls
  • Rear axle protector

Service Concept

Preventive maintenance is made simple with accessible filters and fluid drains. Additionally, the optional auto-lube keep your pivot points greased and ready for the next snow event.