MB |Runway clearing|CRDL
Cradling System
The CRDL features an in-line stowing and cradling design for transport and storage. When the broom is cradled, the casters lift off the ground to eliminate damage during transport and extend caster life.

Sweeping Unit
The CRDL features a 46-inch-diameter broom available in lengths of 18, 20, and 22 feet, providing swept paths up to 18 feet wide. The broom operates at 600 rpm with 4,024 foot-pounds of available torque at the broom shaft at 5,075 psi maximum working pressure. Brush material options include wire, poly, or alternating. The broom head also features amber and red marker lights.
Working Speed: The listed “working speed up to” indicates the estimated maximum technical speed the equipment can achieve. It does not represent the recommended operating speed. Actual operating speeds must always be adjusted to the prevailing weather and environmental conditions.
Broom Unit
Broom Head Configuration Options
The broom frame is 102 inches wide, while the broom head configuration options include:
- 20-foot broom length
- 22-foot broom length
- Broom Power Package Options
The optional Broom Power Package includes a Caterpillar C13B 496 HP electronic turbocharged diesel engine that is T4F EPA/Stage 5 emission certified. It is available with a 500 rpm broom providing 4,828 foot-pounds of available torque at the broom shaft at 5,075 psi maximum working pressure.
Broom General Options
- Automatic brush pattern adjustment
- Broom head vibrator
- Ground speed control, requiring automatic brush pattern adjustment and broom speed tachometer
- Broom hydrostatic pressure gauge
- Auto stripper bar adjustment system, requiring automatic brush pattern adjustment
- Snow shed hood
- Rear-view color camera system
- 13 pounds of poly/wire alternating wafers in place of all poly wafers
- Cassette brushes for faster replacement, available as single or dual core in poly, poly/wire, and all-wire bristles
- Broom Spare Parts Options
Broom Spare Parts Options
- Broom chassis axle, tire and wheel
- Set of broom cores
- Set of four non-adjustable broom carts
- Set of two end plate jacks for core change
- Caster tire and wheel, nitrogen filled
- Caster tire, wheel, hub, bearings, axle, and nuts, nitrogen filled
- Caster tire and wheel, foam filled
- Caster tire, wheel, hub, bearings, axle, and nuts, foam filled
- All-poly, all-wire, or poly/wire alternating wafer kits
Blower Unit
The CRDL is equipped with a dual-impeller, forced-air blower producing 23,000 cfm at 410 mph total.
Drive
The standard broom power package features a 375 HP electronic turbocharged diesel engine that is a Caterpillar C9.3B T4F EPA/Stage 5 emission certified. The engine includes ether start and a heated fuel water separator. A 150-gallon fuel tank provides approximately 12 hours of operation. The engine is housed in a butterfly fiberglass enclosure with hand power assist.
Motion Control
The CRDL features a 25,000-pound electronically controlled steering axle with ABS brakes and automatic drift control. The steering system includes provisions for centering and disengaging the axle steering system. The towing chassis determines the turning radius to ensure the broom consistently follows the chassis.
A center rotating bearing ensures the weight and location of the broom head remain on the carrier center line regardless of the position of the broom head. Independent broom head tilt compensates for surface variations and minimizes brush pattern deviation during operation. Broom oscillation is 8 degrees (+/-4°).
Operator Controls
Operator controls in the cab and engine enclosure promote operator safety and operations.
Power Transmission
Gearboxes with keyed tapered hubs prevent loose connections. Hardened steel pilot plates and core sprockets accommodate radial loads, while molded urethane drive cogs provide torque transmission.
Hydraulic and Electrical System
An independent auxiliary electric motor with hydraulic pump supports the hydraulics and jack stand. A battery disconnect switch removes power to the unit, and a broom speed tachometer is provided.
Engine Options
- Broom engine oil pan heater, pad type
- Broom engine block heater, immersion type
- Battery trickle charger, 1.5 amp
- Battery charger, 20 amp
- Battery heater, pad type
- Remote jump start battery lugs
- Hydraulic oil tank heater, pad type
- Fuel heater, pad tank type
- Coolant filter
CRDL Chassis Integration of Towing Chassis
The CRDL Chassis Integration of Towing Chassis option includes:
- Stationary fifth wheel and mounting
- 9,000-lb ballast
- Plow controls
- Rear axle protector
Service Concept
Preventive maintenance is made simple with accessible filters and fluid drains. Additionally, the optional auto-lube keep your pivot points greased and ready for the next snow event.
